煤矿用链锯 FDJ-120风动链条锯畅销链条锯 木材链锯 防爆风动链锯 FDJ-120风动链锯价格 FDJ-120型风动链条锯是我公司精心研制的煤矿巷道支护维修、截割木材的专用工具。代替了手艺刀锯截木材,减轻了人们粗笨体力劳动,又进步截割速度。煤矿井下风源方便,安上风管即可作业,且不受防爆的约束,适用于瓦斯煤矿出产的需求,深受广阔用户的欢迎。
1.矿用轨迹轻型3分钟轨迹重型5分钟三.长处1.90°直切,45°斜切,立式切开一体机。 2.工作速度只要砂轮机的1/60,安全无火花。 3.切缝窄0.5mm,切开外表平整，精度高，无挂渣，无脱碳。 4.锯条使用寿命长，单位切开成本低，一根锯条使用寿命等同于50-80片砂轮切开片，较电能锯节能60%
联系人金经理电话13934240041

使用方法： 1、了解所需切开的资料，如有必要能够经过下降空气压力来下降锯片的滚动速度。 2、确保结实固定了所需切开的资料，避免其移动。 3、气动空气马达时，用手指按压阀杆，然后开端切开。 4、用锯的分量来控制切开压力。关于较软的资料来说，这样的分量现已满足。过多的压力会下降锯片的速度。关于较硬的资料，能够经过加压的方式来下降锯片的滚动速度。切开是坚持锯垂直。锯片的任何扭曲或倾斜都可能下降其使用寿命。（留意：避开切开后可能坠落的碎片。切开行将完成时，切勿使锯碰到您的身体、工件或邻近的其它人员。） 5、封闭空气马达时，开释阀杆。 6、下次切开开端前，锯片有必要坚持运动状况。气动锯时，锯片不能触摸任何外表。 7、断开空气软管时，封闭空气软管阀。断开前，先翻开空气阀给软管减压。 8、更换锯片前，务必断开空气软管，并推进阀杆以开释掉马达内的压力。 9、顺时针滚动调整手柄以便开释锯片导杆上的张力。然后开释侧面板的锁以便翻开侧面板。然后从驱动轮上取下锯片并将其从锯带导杆上松开
FDJ-120手持式气动切割锯 采用德国进口马达，德国进口锯片防爆无火花
联系人金经理电话13934240041

In order to safe operations need to pay attention to the following points: 1, saw the weight to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any distortion or skewed blade may reduce the service life of 2, turn off the power when the release valve. 3, replacing the saw blade before, be sure to disconnect the power supply. 4, clockwise adjust the handle to release the tension on the saw blade guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod. 5, before the start of the next cut, the blade must keep moving. When an electric saw is used, a saw can not contact any surface. 6, what's needed to cut materials. 7, to ensure that the firmly required cutting material, to prevent the mobile. 8, when connecting the power press with your fingers and began cutting stem. 9, disconnect the power supply when the power off valve hose. Before disconnecting, open the power valve and decompress the hose.